Complete Power Steering Rack And Pinion Assembly For 2004- 2010 Toyota Sienna
Posted on December 15, 2021 | By admin
Removing and reinstalling a rack-and-pinion steering system is the same procedure for most vehicles. The only difference is the way it is removed from the frame. In some vehicles, you must lower the subframe to take the system out, while steering racks on other vehicles are located below the frame, and the subframe does not need to be altered. Follow these directions for cars with a steering rack located below the subframe. Set the front tires forward using the steering wheel and lock the steering in place to keep the tires in alignment. Then remove both the positive and negative cables from the car battery. Complete Power Steering Rack and Pinion Assembly For 2004- 2010 Toyota Sienna. Use a jack and jack stands to elevate the car and remove the front wheels. Drain the power steering fluid and detach the steering column lower joint. Remove all nuts from the inner and outer tie rods, and disconnect the tie rod ends from the steering knuckles. Detach the front exhaust tube and place a support below the engine. Remove the center member and all nuts attached to the engine mounts. Remove all nuts from the bulkhead hole cover and move the cover aside. Take the lower joint off the rack and pinion. Remember the steering neutral position by making a mark on the pinion housing and shaft. Detach the power steering fluid pipes and mounting bracket bolts, and then remove the rack and pinion altogether. Guide the new rack and pinion into position and replace the mounting brackets. Tighten the nuts to 54-72 foot-pounds of torque. Connect the power steering fluid pipes to the rack and pinion. The lower pressure line should be torqued to 20-29 foot-pounds and the higher pressure line should be torqued to 11-18 foot-pounds. Align the lower steering joint and pinion shaft, and torque to 17-22 foot-pounds. Replace the bulkhead hole cover and tighten to 36-43 inch-pounds. Replace the front stabilizer. Place the engine mounting center member back into position, tightening all bolts to 57-72 foot-pounds. Then take the support out from below the engine. Tighten the nuts on the tie rod ends to 22-29 foot-pounds and secure a new cotter pin in place. Install all other objects in the opposite order of their removal. Fill the power steering reservoir with fluid, and then bleed the system. Perform a four-wheel alignment if needed. Compatible with the following vehicles. Rack & Pinion Complete Unit;Steering Rack;Steering Gear. Corrosion and rust prevention. Backed by satisfying after-sales service. Rotate quickly and normal position. 26-2619; ;Rack 25935;3110203;36R0938. Rack replacement kit, rack and pinion, power rack parts. Power Steering Rack;Steering Rack and Pinion. Rack and Pinion Assembly, Rack and Pinion Rack Gear. Top performance For long service life. TOYOTA SIENNA 3.3L. 2003 Toyota Avalon XL Sedan 4-Door 3.0L. International Buyers C Please Note. These charges are the buyers responsibility. Q: How do I return an item? Please contact our customer service before you return an item. If you are dissatisfied for any reason, please do not be quick to leave negative/neutral feedback. Key or key case. Cylinder Piston Gasket Kit. Cylinder Head Gasket Sets. UTV & ATV Brake System Parts. Kevlar Carbon Brake Pads. Brake Rotors and Pads. Nerf Bars & Running Boards. Mass Air Flow Sensor-MAF. Variable Timing Solenoid (VVT). Motorcycle Carburetor & Parts. ATV Rear Wheel Axle. ABS Wheel Speed Sensor. Idle air control valve. Transfer Case Shift Motor. Secondary Air Injection Pump. Spark Plug Ignition Wire. Air Cleaner Filter Box. Cold Air Intake Kit. Oil Catch Can Tank. Fuel Shut Off Solenoid. Air Ride Suspension Valves. Calipers & Rotors Pads. ATV Brake Master Cylinder. Throttle Cable Carb Bracket. Oil Fuel Hose Line. LED 3RD Brake Light. Wheel Hub Bearing Knuckle. Wheel Stem Air Valve Cap. Splash Guards & Mud Flaps. Light Bar Mount Bracket. Other Golf Cart Parts. 4 pcs wheel hub bearing. Tire Inflator Air Pump. Brake Line Lock Kit. Other Handlebars & Levers. Brake Line Tubing Kit. Kick Start Starter Lever. AC Compressor Control Valve+A. Car Window Film Tint Tools. Lower Kits & Parts. Shift Knobs & Boots. Pivot Brake Clutch Lever. Drop Spindle Lowering Kit. 2x Front Hood Gas Lift Supports Struts Shocks Springs For Dodge Ram 02-10 4364. 2x Front Hood Lift Supports Shocks Struts For Dodge Ram 1500 2500 3500 4500 5500. Pair (2) Front Or Rear Wheel Hub Bearing Fits Chevy Impala Buick LeSabre Venture. 2 X Front/Rear Wheel Hub Bearing For Buick LaCrosse Century Chevy Impala Venture. For Ford F-150 Expedition 5.4L 4.6L Explorer Lincoln DG508 Ignition Coil 8 Pack. Fits 04-09 Toyota Sienna Acrylic Window Visors 4Pc Set. 2pcs for 2011 Buick LaCrosse 3.6L Upstream Downstream Oxygen Sensor O2 02. For Chevy GMC Suburban C/K Tahoe Yukon Foldable Power Side View Mirrors Pair Set. 2pcs Front Lower Control Arm Suspension For 2004 2005 2006 2007 Suzuki Aerio. The item “Complete Power Steering Rack And Pinion Assembly For 2004- 2010 Toyota Sienna” is in sale since Friday, May 29, 2020. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Steering & Suspension\Gearboxes, Rack & Pinions”. The seller is “topcn-autoparts” and is located in Ontario, California. This item can be shipped to United States.
- Brand: topcn-autoparts
- Manufacturer Part Number: TA10884601P
- Type: Rack & Pinion Complete Unit;Steering Rack;Steering Gear
- Performance Part: Yes
- Installation method: Performance/Custom
- Fitment Type: Direct Replacement
- Material: High Quality Steel
- Surface Finish: Polished, Rust Protected
- UPC: Does not apply
- Manufacturer Warranty: 3 Years
- Vintage Car Part: Yes
- Rack Type: Hydraulic
- Greasable or Sealed: YES
- Other Part Number: Steering gear
- Rack Material: corrosion and rust prevention
- Note: Backed by satisfying after-sales service
- Advantage: Rotate quickly and normal position
- Interchange Part Number: 26-2619; ;Rack 25935;3110203;36R0938
- Superseded Part Number: 4425008040;4550309250;4425008041
- OE/OEM Part Number: rack replacement kit,rack and pinion,power rack parts
- OE Number: Power Steering Rack;Steering Rack and Pinion
- Sub Type: Rack and Pinion Assembly, Rack and Pinion Rack Gear
- Package: Dust plug
- Universal Fitment: No
- Itment Note: Top performance For long service life
- Mounting Hardware Included: As the picture
- Fits: TOYOTA SIENNA 3.3L
- For: 2003 Toyota Avalon XL Sedan 4-Door 3.0L